WATER TESTING 64 Person Enclosed Lifeboat For The FIRST Time!!

AYO Fishing
Visualizações 1 574 588
99% 46 000 1

Publicado em


28 Nov 2022



Baixar vídeos:

Carregando o link.....

Adicionar a:

Minha playlist
Assista mais tarde
Comentários 3 527
Kozak Outdoors
Kozak Outdoors 2 meses atrás
I ran the serial number and the manufacturer actually created this vessel with the intention of it being launched into LoJo’s pond
LeQuietKid 7 dias atrás
@J As the boat, I can also confirm
Barry Sarver
Barry Sarver 19 dias atrás
He will kill you guys. Lol 😀
Vannessa Silva
Vannessa Silva Mês atrás
Should have offered all of them a tour
يحيى سلامي
Mike Strongerton
Mike Strongerton Mês atrás
yes , i just watched that video its the same lifeboat video ftom over a year ago 😚
Graeme Hay
Graeme Hay 2 meses atrás
It’s called a TEMPSC (Totally Enclosed Motor Propelled Safety Craft). This one is from the Safe Brittania semi-submersible rig (a rig I personally spent some time on in the UK North Sea many years ago) which was generally used for floating accommodation. Judging by the serial number the manufacturer is Schat-Harding, a Norwegian company who specialises in this type of craft. As it was used on a rig it will have been very well maintained as there are strict SOLAS standards that apply. The unit has a lot of features that you won’t know about such as external water spray to allow it to motor through sea surface fires plus it would be pressurised in use to prevent gas ingress. Also, if I recall correctly they are also designed to be self-righting so can’t capsize (I guess that would require all the seals to be intact and the doors closed!). The exhaust fumes inside are a bit worrying as you either have the hull exhaust plugged (this would likely be under the water line) or a manifold leak, either way it should be easy enough to figure out. If you were to contact Schat-Harding with the serial number there’s a good chance that they would still have all the documentation for the vessel, worth a try.
What In The World Is That!?
Too bad nobody in the comment section knew anything about this
Ojb 1959
Ojb 1959 21 dia atrás
I didn’t work on the Britannia oil rig however I did stay at a Holiday Inn Express once. Great channel 👍🏼👍🏼
Jormungand13324 22 dias atrás
you think the hull exhaust is that round hole at the bottom of the craft that was plugged at the start of the video?
Oliver Dorado
Oliver Dorado 23 dias atrás
To have
Paul Mês atrás
@Derek Sleight Right, was thinking same thing ..
steven allen
steven allen 2 meses atrás
Sweet boat, A tip for fiberglass repair especially the one on the bottom. Use a small 1-2 inch medium coarse disc sander and remove material around the hole down 3-4 layers, the next step is to go 3/4 of an inch larger and sand to one layer above the last . do this until you reach the last layer at the surface. Cut each patch to fit each layer. Its kind of like a step drill in reverse as you look at it. Then mix your resin and install the fiberglass one layer at a time make sure to remove the air bubbles if you see any. Also types of glass maybe use some thicker matt for the first two layers the cloth for the remainder. I think you could use a plastic flexible cutting board to hold the repair in place using a 2x4 holding slight pressure behind the plastic cutting board. Once it sets up the plastic should peal off. Sand and paint repair or gel coat.
Jason Witt
Jason Witt 19 dias atrás
i think he patched over the water intake for the motor cooling line
Guinness Mês atrás
Good advice
Adrea Brooks
Adrea Brooks 2 meses atrás
Great tips! I'll be keeping these in mind! (Hope AYO sees em. XD )
Webster Forrest
Webster Forrest 2 meses atrás
This boat looks so cool. I love how the engine is just ready for action every time. This could be such an awesome houseboat. Thanks for posting.
David and Kelly Inancsi
MAN! THAT WAS AWESOME! Seeing these boats on other ships when I was in the Navy, I always wanted to take one for a spin. GREAT purchase! Fair winds and following seas…go to your instagram page. I sent you some photos.
Dasquadwith6 2 meses atrás
It was actually pretty cool to see one of those that wasn't hanging off a larger vessel "for emergency only". When the CO alarm sounded, you did the best thing you could have...headed outside to fresh air. Good video.
Preston Thomas
Preston Thomas 2 meses atrás
I worked offshore for several years and I can tell you those safety boats have been known to have made some people so sea-sick they actually died from aneurisms. You get on one of those in an an off-shore emergency it was truly a last resort. I myself use to hide whenever they had rig drills where they actually dropped them in the water with people on board. Nope, nope, not doing it. Their cool looking though. Good luck with the restoration.
You know me
You know me 2 meses atrás
As a young man, I learned to captain a boat on the black sea, 1980 while stationed in remote Turkey. That looked so damn fun to run, congratulations on your purchase.
Bamcorp Gaming
Bamcorp Gaming 2 meses atrás
happy it all worked out. looking forward to the adventures you have with it. hoping you fix it up real nice and take it on some long adventures. ive seen tons of vids and articles about people converting these into homes and living in them full time out on the ocean. its pretty damn cool I hope you take care of it and look forward to your future vids with it.
John Doe
John Doe 2 meses atrás
Hey Ayo, congrats on getting that awesome boat, dude! I can imagine some haters saying you're nuts or whatever, but what the hell, hater's always gonna hate, and most of that nonsense is just pure jealousy. Personally I think if you're crazy, then it's a cool kind of crazy, and I wouldn't mind being crazy myself with a bad ass lifeboat of my own! I never saw any lifeboats that weren't attached to either a cruiseship or an oil right, and that was mainly in movies or documentaries, so I had no idea those boats could be put on a trailer, let alone owned by a private person. I have always been attracted to the idea of owning a boat, but the tought of getting caught in a storm in the middle of nowhere and having my boat or yacht capsize always scared the hell out of me, so I pretty much just gave up thinking about owning any boats. Then I ran into your video of when you were going to check out the boat and buy it, and I saw the footage of the lifeboat getting jettisoned from the oil rig, plunging into the sea, then bouncing right back to the surface, and I realized this is the type of boat I've always wanted and I didn't even know it, so congrats again on buying your boat, and thank you for making these videos, man! Thanks to your videos, I know now which direction I wanna go about owning a boat. I also realize now that if and when I buy my own lifeboat, I won't be as afraid of getting caught in a storm as I've always been since lifeboats are designed to be pretty much uncapsizable. Of course, weather reports and storm warnings must always be taken heed of, though, even in a lifeboat. I also understand I have a ton of research ahead of me, before I even try to find a boat for myself, but it's something cool to look forward to. Anyways, watching your video of the first time you put the boat in the water and how the engine makes so much damn noise and creates a health hazzard inside the boat by the fumes it makes, reminded me of another video about a lifeboat, which I saw shortly after your video about when you first checked out the boat with the nice old cowboy guy. It's a video about two european guys who got a lifeboat and turned it into a house boat, making it all electric and solar in the process. Here's the link to that video, I hope you like it and find it useful to your own experience: Please keep us posted about your progress with your awesome lifeboat. Goood luck, dude, and Happy Hollidays!!
Sturvin Murvin
Sturvin Murvin 2 meses atrás
Seriously this is cool. I really enjoy these older machines and there are a ton of uses for this boat! Love it!!
Abdiel Carvajal
Abdiel Carvajal 2 meses atrás
I’m not an expert filling holes in boats, but back in the time when I was surfing, I was able to fix quite a lot of holes in my surf board. We used Fiberglas and covered with resin. I would sand the area around the hole first, the apply an even amount of resin around the hole, covered with a thick layer of fiberglass and even more resin, place some paper wax and a piece of wood, from the bottom to keep the fiberglass in place and pressure using a jack and a rod. The paper wax its to avoid the wood sticking to the resin.
MegaEverythingElse 2 meses atrás
Have you ever considered that the hole you guys plugged in the bottom of the boat would be the exhaust? with that plugged maybe it pressurised the motor box and the only way out was through tiny cracks into the interior of the boat. That hole looked a little too perfect to be just a random hole into the inside......
TDSG34 2 meses atrás
haha! That was one of the best videos I've seen in a long time - from watching your fiberglass skills to actually running the boat! Never seen anything as unique as this. Loved it!
Tertamsta 2 meses atrás
I would recommend to grease up the seals. That way they don't stick together every time you leave the hatches closed for a while. Super interesting video, love to see more!
Anders Larsson
Anders Larsson Mês atrás
Great video! This lifeboat was built in my hometown of Gothenburg in Sweden in the early 1980. The offshore-industry were blooming in thoose days, and we had oilrigs al over the world. Looking foreward to follow you around the world 😂. Regards from Sweden
Perry McClusky
Perry McClusky 2 meses atrás
Congratulations on a successful first time out on the water! Looking forward to your next video on this craft.
Alex Russell
Alex Russell 2 meses atrás
Wish I had a skill I could market to you, but I don't think my amateur photography and editing skills would make the cut. You're living a dream of a life I'll never have. And you deserve every bit of it, man. Great attitude, even-tempered (or should I say even-keeled?), no BS. You make a lot of folks' days, mine included. Thank you for that.
darkerthandark69 2 meses atrás
Couldn't of said it better myself my friend I agree your not alone
Alex Russell
Alex Russell 2 meses atrás
@Tombomb1816 I'm a details guy. Not terribly creative, or at least not *efficiently* creative. I can spend an hour scrutinizing and rewriting a single paragraph. I'd be a great copyeditor, but not a copywriter. Regardless, you give good advice. Hard work often pays off. I'm in my 30s though. No kids, doesn't look like there will be any. I quit college to start my own business and it failed during COVID. Being the type to work 18-hour days given the chance, seeing that effort go nowhere but downhill is humbling at the very least. Just a reminder though: sometimes, things don't work out. The key is to not put all of your eggs in one basket. I did. Big mistake.
Tombomb1816 2 meses atrás
Respectfully if you were motivated to be the best videographer you possibly could and worked hard you would be good enough to make the cut. If it was a real dream and you truly wanted it you would do it. Some people want things but not bad enough to make it happen.
onedwn1613 2 meses atrás
love the joy in this one! congrats on the win. the partners yoga simply killed! i do love me some Mr Gravy
koreanjeep Mês atrás
Awesome video! I really like your content! I don't know anything about this specific boat, but I saw some Norwegian instructions and components in there! I'm from Norway and have been working offshore on oilrigs a few times 🙂
halfwaymo 2 meses atrás
Omg what a deal--I’d love to own one-solar panels on top, gas gauge, beds, kitchen man you got a dream boat...congratulations......Missouri 💙
Drop Anchor
Drop Anchor 2 meses atrás
This is awesome! Looks like the perfect vessel for an overnighter!😂
Christopher Hofheins
Christopher Hofheins 2 meses atrás
Now that has to be featured for an “over night” fishing trip!!! Or weekend excursion, just needs an a/c with generator to stay cool with the hatches closed
Rod Croskery
Rod Croskery 2 meses atrás
It must have been interesting running it onto its trailer with that steering gear.
JFinnerud 2 meses atrás
Backing is basically a "joke" on those types of vessels. I've always practiced backing only when needed and using the revers/forward when turning and they will basically turn on a dime. I spot a few technical solutions as well as hull design which are similar to the Norwegian Viksund fishing vessels. Anyways it's cool to see it afloat. You'll get the hang of the controls in a breeze. 👍👍
Dean Woods
Dean Woods 2 meses atrás
Your genuine excitement definitely transfers through the video! 👍👍👍
S. E. C-R
S. E. C-R 2 meses atrás
I think I would have been terrified the whole time, but it ended up being pretty cool! I would have liked to see some of you loading it back on the trailer and pulling it out though.
Danny Donovan
Danny Donovan 2 meses atrás
Love your videos. You could have used magnets to hold up the sheets of fiber glass
Murray Ball
Murray Ball 2 meses atrás
Being built as a safety and life saving device, it should be built reliably and tough as nails. Carbon Monoxide alarm is legit and the alarm is another level of safety. Easy fix for you to ensure the gas doesn't get into the boat again. That engine is reliable AF unlike a domestic outboard can be. This thing was built to sit in place for years unused - although I do believe that they have to be tested periodically to ensure they are ready to go in an emergency. Great score man, and great vid - glad it all went well. Cheers.
Lazurkri 2 meses atrás
I've seen people turn the smaller versions of these into like houseboats and it works pretty well for them; the sea keeping on them is a little bit of a pain in the ass because these really aren't meant to be used long term in the water, they're meant for short term survival stuff but because they're so reinforced and overbuilt because, you never know if the sea is going to be calm rough or on fire if it's a oil rig escape craft, you can do a LOT with them, and because 64 men is a LOT of weight, if you only expect to have at most a dozen people inside, that gives you a LOT of reserve buoyancy to use for gear and other amenitie. That top rail for example is PERFECT for strapping solar panels to, either on top or angled down to the deck to fit more panels too; I've seen pictures of one of these style life boats that someone stuck batteries and solar panels in with a backup diesel motor in and they were able to sail at a decent 10-15 knots for a few hours without even getting close to emptying the batteries.
Deleted Comment #2
Deleted Comment #2 2 meses atrás
How far can the vessel travel when fully loaded with fuel?
the squatch m249
the squatch m249 2 meses atrás
I think once it's past testing, a 7 day catch and cook on this must happen.
BP23 2 meses atrás
Happy for ya brother! Been watching since the house boat purchase! Keep up the great content!
Luiz Nunes
Luiz Nunes 2 meses atrás
This is fantastic! I wish I could, then I'd go work for you for free because I love laughing. 😆
PopTart Mês atrás
It would be cool to see it built out on the inside to make it a nice weekend boat to hang out in.
P Stoneking
P Stoneking 2 meses atrás
It seems weird that hole was perfectly round. I probably would've used a rubber expanding plug instead of fiberglass it closed.
Jason Dunbar
Jason Dunbar 2 meses atrás
Dang it I was really wanting to see you guys loaded onto the trailer. I have a feeling that was probably interesting to see
Red Shed Acres 6625
Red Shed Acres 6625 2 meses atrás
My grandson has your eyes when he is loving whatever he is doing. I sure hope he can direct his enthusiasm in the same positive ways that you are doing. You have a gift. Don't let others throw anything negative your way. Keep it up.
Brian "Six" String Lee Mayes
Before you get too far on this project, I hope you checked out the videos from others who have refurbished these things. Pretty awesome things they've done to them.
kls2020 2 meses atrás
You could replace the hand crank steering wheel with a DC motor drive with a Left /Right switch to turn the rudder so you don't have to do all of that cranking . Adding an indicating gauge to show rudder angle position would keep you straight on direction .
braggarmybrat Mês atrás
@Riordan Henry Better yet, have a compliment of slaves to oar the thing around. I think Augustus, Nero, and Caligula had the right idea. 😝
kls2020 2 meses atrás
A 24 volt electric valve actuator might work best for converting the steering system instead for a few reasons . Drives electrically in both directions , has a handwheel you can still use for manual operation if desired (that declutches when electrically operated) . already has analog circuitry for indication for showing valve (rudder) position .
John Doe
John Doe 2 meses atrás
Genius ideas, sir.
Riordan Henry
Riordan Henry 2 meses atrás
Too much complexity! Replace all steering and propulsion with giant (and I mean GIANT) trireme sytle. Simple = better
rmp5s 2 meses atrás
Then you could grab a GPS receiver a Raspberry Pi running ArduPilot and BOOM! Programmable, fully automatic navigation. 👍
markthomasbuilder 2 meses atrás
That diesel sounds great! Looking forward to see what you do next.
jack sampson
jack sampson 2 meses atrás
I'm so excited to see you get this and make videos I have wanted one for years You should get it sealed up good and tight and do a video Where you put some beds in it and do a video Staying the night inside it during a bad storm that would be so awesome
Matt Bobo
Matt Bobo 2 meses atrás
When patching a hole in fiberglass always start with a piece of the mat and form it to the inside of the hole.
Dettweiler / DJ Dett
Dettweiler / DJ Dett 2 meses atrás
Definitely needs a starter/cutout switch at the helm!
Loaves & Fishes
Loaves & Fishes 2 meses atrás
All I can think each time I look at this boat is what an amazing “houseboat” it would make! So much fun to watch your videos! I’m a 63 year old Grandma, but I love your videos, you guys make me laugh and giggle like a girl again.
Sunny Scott
Sunny Scott 18 dias atrás
LOL>>I am a 75 year old grandma and that was actually my very first thought. I thought he was buying it to make it into a tiny house!!
Dan Smith
Dan Smith 22 dias atrás
These guys did it, and then took the boat to the Arctic:
Joe Lex
Joe Lex Mês atrás
I thought the same thing. Houseboat build just waiting to happen.
Guinness Mês atrás
@Tina Stormcaller they won’t fit in any locks so you won’t be going very far on the canals in them. Be ok on the Thames though
Tina Stormcaller
Tina Stormcaller 2 meses atrás
There’s a bunch of people who use these as houseboats in London, as a less canal-capable but more sea-capable alternative to the narrowboat
Colrie Gardener
Colrie Gardener 2 meses atrás
Wow! i used to operate one like this when working on a cruise ship, it should be a double hull insulated boat even if its full of water it shoud not sink, a 3 sylinder engine, steering is water jet turn slowly not strong handeling in ruff sea, the engine is verry reliable it steering is small and you has to turn it a lot it is 3 man operated a bow man a stern man and the captain, 2 switch battery system cold start warmer for engine. i love it i would put a more powerful engine in it and blade rudder then you good to go.
Ben Jocham
Ben Jocham 2 meses atrás
I'd be kitting it right out for a house boat.....I look forward to see what you do with it.....all the best 😉
BDiaz1000 2 meses atrás
An interesting tip. Life boats are designed to hold enough fuel to be able to go at least 6kts for 24 hours.
Esteban Urbina
Esteban Urbina 2 meses atrás
This boat is epic and watching you try it out was fun
threefiftyzzz 2 meses atrás
An overnight fishing trip in the lifeboat with Ayo, Norm, Lojo and Davey Gravy.. This has gotta happen!
Jeff Burnham
Jeff Burnham 2 meses atrás
@Heather Howard I think it's a law in most states that vessels of that size must have navigation lights, and other items as well.
Jeff Burnham
Jeff Burnham 2 meses atrás
He just got it floated, do you really think its wise to have Norm and Lojo also onboard?
Michael G.
Michael G. 2 meses atrás
But then there's still room for 60 more people- 59 if Darrell can make it. Let's fill that suckah up!
jammin2070 2 meses atrás
Mary Brown
Mary Brown 2 meses atrás
@Heather Howard not with modern LED lights...
Karl - Udo Becher
Karl - Udo Becher Mês atrás
I would love to have one , totally cool. Out of interest how big is the diesel tank? Those motors do not use a great deal of fuel.
SY Delina
SY Delina 2 meses atrás
I am a little concerned about the cooling of the engine. Most inboard engines are cooled by seawater which is - after used for engine cooling - lead into the exhaust to cool down the exhaust gases before the exhaust is led through the hull. I didn't see any water coming out of the exhaust ! Probably the seawater valve is closed, the water pump impeller is broken or ... you sealed the hole for the cooling water ;) . Also, the anodes ( hull, motor, perhaps gear, shaft ...) should be checked! Because the boat was build for Saltwater they are made from zinc, but for permanent use in Sweetwater they should be replaced by aluminum or magnesium.
Adam Martin
Adam Martin 2 meses atrás
that thing is sooo cool and has massive potential to become a very nice boat
Ray Cecil
Ray Cecil 2 meses atrás
"Its like a human microwave for flatulence..." My man....I just tooted a little because I laughed so hard.
Ace Smith
Ace Smith 2 meses atrás
I'm not a boater and I don't do too much fishing but I watch your videos and can appreciate your tenacity and optimism. You got to love when you bust your a** on a project and IT WORKS! Seeing this lifeboat move made my day. To be honest this is one of the only channels I watch from start to finish that are videos longer than 5 minutes because you never know what's going to happen next.... Keep em coming bro! Can't wait on the itty-bitty update fam.
Wolfy100 2 meses atrás
I lol'd at "burst your a**"
gjerdeanders 2 meses atrás
A tip for you. Lube the seals around the hatches with petrolium gel, and they will never get stuck again :)
Gryphon Arms USA
Gryphon Arms USA 2 meses atrás
Definitely fix that exhaust leak and put a starter/kill switch at the pilot station. I would put in a few more portholes and turn it into a houseboat. Put teak deck topside on either side of the center walkway that has sections that lift with the hatches. I’d like to have one, but what I’d really love to have is a 26’ jet drive, shallow draft, double hull landing craft with a sleeper cabin. I would use it for fun and flood rescue. Only problem is I’d need to get a truck to pull it and it’s really just a dream/wish, because a disabled vet without any benefits, and not able to work, ain’t buying anything sooner or later. 😥
Kyle Trescott
Kyle Trescott 2 meses atrás
Try using slimy grimy to clean the rest of the hull! Stuff works great!
Carlos Tavares Jr
Carlos Tavares Jr 2 meses atrás
Pretty cool! First mod would be to relocated starting to controls to the console then lights, lights everywhere!
SargeantSquatch 2 meses atrás
It's probably pretty safe to say you have a one of a kind boat. Not many people have an off the oil rig escape boat, much less one on a custom made trailer. This is rad lol, been a subscriber for awhile and you're type of content isn't usually my jam. But something about your personality and way of presenting the content I'm all about. Keep on keeping on man!
B 2 meses atrás
Put in a few bunks and more of a kitchen and you'd have an unique air BNB
bill richardson
bill richardson 2 meses atrás
I wonder if its the resemblance to Bam Margera?
NoSpoon 2 meses atrás
There are a few about on youtube. A nice liveaboard and even a submarine.
Trace Dirks
Trace Dirks 2 meses atrás
@J same here. Haven't fished ever but I watch most of the Googan gang. Personality and genuine excitement is why I tune in.
J 2 meses atrás
Same. Never fished in my life but Ayo's nautical adventures have kept me coming back over and over, lol.
Robert Smith
Robert Smith 2 meses atrás
I can't wait to see the future of your boat with seeing other owners of similar types. Look up "yachting world" on BRvid there is a similar boat converted into a cool living space.
Djendo 2 meses atrás
Would be awesome to convert this to a little home on the water!
ttnyny 2 meses atrás
With those fiberglass skills, a big budget and lots of time, you could mock up the lifeboat as a surface-navigating replica of The Yellow Submarine.
Ink le nation 1972
Ink le nation 1972 2 meses atrás
That was awesome!!.. I could live on that quite happily with only a few minor adjustments….
Torhs11 Nettie
Torhs11 Nettie 2 meses atrás
So happy to see things work out for you regarding a boat purchase finally! Seeing the genuine appreciation is awesome
jawsjulie 2 meses atrás
But did it?
Cølin 2 meses atrás
Are you gonna build it into a houseboat? That would be AWESOME.
Edith Gomez
Edith Gomez 2 meses atrás
You both made my day better!!!! Thank you!!!!
youlooze2me 2 meses atrás
you probably should have started it when it was on the trailer and felt if exhaust was coming out that hole in the bottom. Or put a borescope up through it to make sure it didn’t go to the engine area.
Barbarian Leather and Blades
Any time your sealing up a boat you should use 5200. It is for marine use. Regular sylicone won't last.
Miles Welch
Miles Welch 2 meses atrás
I would really recommend getting this boat seen by a marine surveyor if only to identify the unknown electronics and fuel capacity/gauge, as well as overall health of the fiberglass and hull overall.
Leatheryman 2 meses atrás
Great to see that thing in the water. So many possibilities. Happy for ye
Preston Russell
Preston Russell 2 meses atrás
Awesome video,a great success. Congratulations!
ChasinKansasBass 2 meses atrás
I would love to work for you man I’m in Kansas but love the energy and this is the space I want to be in
ChasinKansasBass 2 meses atrás
I would literally eat saltines and sleep in a tent for a chance lol
Jonathanislas 2 meses atrás
Cant wait for part 2 man!
Martin Betzner
Martin Betzner 2 meses atrás
That hole in the bottom may have been the exhaust port or water intake. You may want to check before next time out.
Ali G
Ali G 2 meses atrás
@Derek Madden Its a simple plug hole. (screwed fitting)
Ali G
Ali G 2 meses atrás
@Chris clark (Mercury207)They aren't self bailing. The drain plug has to be removed or replaced manually from inside the boat. it's kept on a lanyard by the drain hole.
TheMcspreader 2 meses atrás
It might also have been a moon pool for mice but the likelihood is similar.
Landrum 2 meses atrás
I agree, very likely that hole is a subsurface exhaust or intake for sea water engine cooling.
Derek Madden
Derek Madden 2 meses atrás
@J did you even read the original comment you’re replying to? There are more possibilities for the hole rather than simply a plug hole. Regardless, I didn’t speculate one way or the other. I just corrected your original comment. If you’ve ever been around big boats you would know there are many reasons why a hole could be found on the hull of a boat.
TVill29 2 meses atrás
So hyped for you that’s so damn cool!!!!
Walter Steenvoorden
Walter Steenvoorden 2 meses atrás
Seen these on cruiseships as lifeboats. Modern types can even provide entrance for people with physical disabilities.
lucian warren
lucian warren 2 meses atrás
I thought it was the same life boat in southern harbor. Cool to know it actually is 😂 if you ever need help with working on it or any help with any projects let me know. I live on county road 222. When I seen it I was like wait a minute is that the same one? Or did someone else buy one too😂
Making Waves Presents
Making Waves Presents 2 meses atrás
it`s possable its the raw water inlet you blocked up from the position under the boat, most marine engins are cooled by a heat exchanger and pass raw water out of the exhaust, as no water was comming out of the exhaust it was possably the engine overheating that set off the alarms.
big d
big d 2 meses atrás
"Ive never bought a boat that actually works" spoken like a true face book marketplace professional.
ben helie
ben helie Mês atrás
I subscribed because this interests me. Fishing is in your name, I want to see some people fishing out this bad boy
Noah Gossett
Noah Gossett 2 meses atrás
A nice rough sanding on the fiberglass will help adhesives for your patch work
Quinnebaug 2 meses atrás
Do you think it'd be wroth moving the ignition/kill switch to the drivers cab?
CRUecke 2 meses atrás
I would check if the hole you patched was actually the exhaust port for the motor. It looked almost perfectly round.
TimmyNoShoe 2 meses atrás
Pretty sure on the first video they said it was cut in to drain water from the inside while it was sat on dry land
rickss69 2 meses atrás
That was the first clue for sure...
Errol Pippin
Errol Pippin 2 meses atrás
You need to use a brush and coat the surface first then put your cloth on and stipple it with more resin and you should have removed paint to access the raw fiberglass so as to achieve adhesion and then add multiple layers
Alienated To The World
Alienated To The World 2 meses atrás
Well at least with the fumes the boat also passed the flatulence test lol
Liamlaoch 2 meses atrás
Bro this would make a kick ass weekend boat for a couple. Pretty much do a van life build but on a life boat.
The Representative
The Representative 2 meses atrás
Congratulations Brother 🎉🎉❤
Elam Fisher
Elam Fisher 2 meses atrás
Yes!!! Freaking love your content!! Thanks so much for the many hours of amazing content. Nothing makes me forget a stressful day like a new Ayo video!!!
Riordan Henry
Riordan Henry 2 meses atrás
An actual launch is probably out of the question. Next best thing: you + 63 more people. The Party Bouy Also, when you finally fish on this thing, you're a lot less likely to drop your bass back into the lake hehehe
Lobot Mês atrás
That's the doomsday boat for sure. lol Pretty awesome!
Simple Ranch
Simple Ranch Mês atrás
Great video! Had my attention the whole time.
Schalk Burger
Schalk Burger 2 meses atrás
I think the hole you plugged might have been the fume outlet?
Zwifting With Granny
Zwifting With Granny 2 meses atrás
Please, please, please give us videos of yours more often. It's the highlight of my day when I see you have a new video out. I don't care what it's about. The chemistry you have with Davey and also with Norm are the best. You can handle it yourself or you can do collabs with them, you can do it all. Your comedic timing is impeccable, your delivery is perfect and the facial expressions and camera stares just are right on target. Thank you for putting this video out today. My dog died last night and your video is the first time I've cracked a smile all day.
Zwifting With Granny
@Becca Thib Thank you so much.
Becca Thib
Becca Thib Mês atrás
I'm sorry about your dog dying. It's the saddest thing in the world...🙏
Zwifting With Granny
Zwifting With Granny 2 meses atrás
@Tyler Woody agreed, but he did also say he was looking for a new camera/editing guy. Whoever the current person is does a great job. An excellent job. But possible someone in the future might be able to provide us with more content. That's my hope anyway. If not, I will just look forward to the videos as they come out.
Tyler Woody
Tyler Woody 2 meses atrás
Quality over quantity
Zwifting With Granny
Zwifting With Granny 2 meses atrás
@Loaves & Fishes isn't that the truth.
warren thomas
warren thomas 2 meses atrás
Did he ever mention what he paid for it?? I can see this being used for overnight stays or even a lakeside bar & grill. Cutting away most of the side walls and putting windows in and you got something that no one will forget
Chicken_dude1 2 meses atrás
they use acid to get the bottoms of boats back to condition again, no need to repaint, use muriatic acid diluted with a little water and a crap broom (it will melt a little) and if your getting carbon monoxide into the engine compartment it will kill your engine power aswell, MUST be an exhuast leak, fiberglass repair is like welding (prep wise) you just have to grind away alot more material to have enough surface area to hold on to when you lay up the glass and make sure to follow up with a good amount of gelcoat for durability
Lee Gliddon
Lee Gliddon 2 meses atrás
You rock dude! That was cool.
live lurked
live lurked 2 meses atrás
Dude that engine looks CLEAN
ML Pencola
ML Pencola 2 meses atrás
I wondered what happened to this vessel!?! Ayo, you should be soooo proud of how far you have coming doing these amazing repairs on your own! Very impressed!
Kinsey Cushman
Kinsey Cushman 2 meses atrás
I work on these for a living! They're decommissioning a lot of usns ships
Larry Anderson
Larry Anderson 2 meses atrás
Make it into a weekend fishing lodge. Like a man cave tiny home for fishing
Is it the volts or amps that kill?
Visualizações 1 000 000
We Built A Homemade Survival SUBMARINE
Turning a BLOB into PURE GOLD!
Visualizações 2 600 000